Huawei Y6 Prime 2018 ATU-L31 Firmware Flash File

The Huawei Y6 Prime 2018 (model ATU-L31) is a budget-friendly smartphone from Huawei. As of my last knowledge update in January 2022, here are some key specifications and features of the Huawei Y6 Prime 2018:

1. Release Date: The Huawei Y6 Prime 2018 was released in April 2018.
2. Display: It features a 5.7-inch IPS LCD display with a resolution of 720 x 1440 pixels.
3. Processor: The phone is powered by a quad-core Qualcomm Snapdragon 425 processor or a MediaTek MT6739 processor, depending on the region.
4. RAM and Storage: It typically comes with 2GB of RAM and 16GB of internal storage. There is also a microSD card slot for expandable storage.
5. Camera:
   • Rear Camera: 13 MP, f/2.0 aperture, autofocus, LED flash.
   • Front Camera: 5 MP, f/2.2 aperture.
6. Battery: The Y6 Prime 2018 is equipped with a non-removable Li-Ion 3000 mAh battery.
7. Operating System: It runs on Android 8.0 Oreo with Huawei’s EMUI 8.0 on top.
8. Connectivity: The phone supports 4G LTE, Wi-Fi 802.11 b/g/n, Bluetooth 4.2, GPS, and a microUSB 2.0 port.
9. Build and Design: The device has a plastic body and is available in various colors.
10. Other Features: Face unlock, FM radio, dual SIM support, and typical Huawei customization features.

How to Flash MediaTek Devices :

1. Download Necessary Files:
   • SP Flash Tool: This is a commonly used tool for flashing MTK devices.
   • MTK USB Drivers: Ensure you have the correct USB drivers installed on your computer.
   • Stock Firmware: Download the official stock firmware for your specific MTK device.
2. Install MTK USB Drivers:
   • Before connecting your MTK device to the computer, make sure the MTK USB drivers are installed. If not, download and install them.
3. Backup Data:
   • Flashing firmware may erase your data. It’s essential to back up your important files and data before proceeding.
4. Charge Your Device:
   • Ensure your MTK device has sufficient battery charge to avoid any interruptions during the flashing process.

Flashing Process:

1. Extract Files:
   • Extract the downloaded SP Flash Tool and stock firmware files to a convenient location on your computer.
2. Launch SP Flash Tool:
   • Open the SP Flash Tool on your computer.
3. Load Firmware:
   • In the SP Flash Tool, click on “Choose” or “Scatter-loading” and select the scatter file from the firmware folder you extracted earlier.
4. Power Off Your Device:
   • Turn off your MTK device.
5. Connect Your Device:
   • Use a USB cable to connect your MTK device to the computer.
6. Start Flashing:
   • In the SP Flash Tool, click on the “Download” button to begin the flashing process.
7. Wait for Completion:
   • The tool will now flash the firmware to your MTK device. Wait for the process to complete.
8. Complete the Process:
   • Once the flashing is done, you should see a success message. You can now disconnect your device and reboot it.

Download Huawei Y6 Prime 2018 ATU-L31 Firmware Flash File

Huawei Y6 Prime 2018 ATU-L31 Firmware Flash File

Join Our Telegram Group. If you have any problems then comment below or message us. We try our best to help you. If you found this post and our site helpful then Dont forget to like and share our page.

Please Follow these Before Flashing :

▶️ Disclaimer: Firmware flashing is not an easy process and should be carried out only if you have enough knowledge. We are not responsible for any damage/ dead to your device.

▶️ Take a Backup: If you are going to flash the above firmware on your Lava device, then make sure to take a backup of your data as it will be deleted after flashing the stock firmware.

▶️ Download and Install the Proper Drivers and Tools required before flashing.

▶️ If You Need Any Other Firmware or Flash File, Let Us Know.