The Benco V80 is a budget-friendly smartphone that was released in June 2021. It has a 6.51-inch IPS LCD display with a resolution of 1600 x 720 pixels and a 20:9 aspect ratio. It is powered by the Unisoc SC9863 chipset and comes with 4GB of RAM and 64GB of internal storage. The storage can be expanded further using a microSD card. The Benco V80 has a single 8MP rear camera with an f/2.0 aperture and a single 8MP front-facing camera with an f/2.2 aperture. The phone is equipped with a 5000mAh battery that supports 10W wired charging. It runs on Android 11.
Here is a summary of the key specifications of the Benco V80:
- Display: 6.51-inch IPS LCD, 1600 x 720 pixels, 20:9 aspect ratio
- Chipset: Unisoc SC9863
- RAM: 4GB
- Storage: 64GB, expandable via microSD card
- Rear camera: 8MP
- Front camera: 8MP
- Battery: 5000mAh with 10W wired charging
- OS: Android 11\
How To Flash SPD CPU Phones :
Flashing a SPD (Spreadtrum) CPU-based Android phone typically involves using specific tools and firmware files to re-install the device’s operating system. Below are general steps to flash an SPD CPU phone. Keep in mind that the exact procedure can vary depending on the phone model, so it’s essential to follow manufacturer-specific instructions if available.
**Note**: Flashing your phone can lead to data loss and, if not done correctly, can render your device unusable. Proceed with caution and ensure you have backups of important data.
Here are the general steps to flash an SPD CPU phone:
**1. Download Required Files:**
– Firmware: Obtain the correct firmware for your phone model and region from the official manufacturer’s website or trusted sources.
– Flashing Tool: Download and install a compatible flashing tool like SPD Upgrade Tool (also known as SPD Flash Tool) or Research Download Tool.
**2. Install USB Drivers:**
– Install the appropriate USB drivers for your phone on your computer. These drivers ensure your computer can communicate with the phone.
**3. Prepare Your Phone:**
– Charge your phone to ensure it has enough power during the flashing process.
– Back up important data from your phone to avoid data loss.
**4. Boot Your Phone into Download/Flash Mode:**
– This step can vary depending on the phone model. Commonly, it involves turning off the phone, holding specific buttons (e.g., Volume Down), and connecting it to the computer via USB.
**5. Launch the Flashing Tool:**
– Open the SPD flashing tool on your computer. Ensure it recognizes your connected phone in download mode.
**6. Load Firmware:**
– In the flashing tool, load the firmware files (usually in .pac or .pac.gz format) you downloaded earlier. These files contain the OS and other necessary components.
**7. Configure Flashing Options:**
– Depending on the flashing tool, you may have options to configure the flashing process. Ensure the settings match your requirements.
**8. Start Flashing:**
– Click the “Start” or “Download” button in the flashing tool. The tool will start flashing the firmware to your phone. Do not disconnect your phone during this process.
**9. Wait for Completion:**
– The flashing process may take several minutes. Once completed, you should see a success message.
**10. Reboot Your Phone:**
– Disconnect your phone from the computer and restart it.
**11. Set Up Your Phone:**
– After rebooting, your phone should be restored to its factory state. Follow the setup wizard to configure your phone as needed.
Download Benco V80 Dump Firmware BY CM2 SPD
Benco V80 Dump Firmware BY CM2 SPD
Join Our Telegram Group. If you have any problems then comment below or message us. We try our best to help you. If you found this post and our site helpful then Dont forget to like and share our page.
Please Follow these Before Flashing :
▶️ Disclaimer: Firmware flashing is not an easy process and should be carried out only if you have enough knowledge. We are not responsible for any damage/ dead to your device.
▶️ Take a Backup: If you are going to flash the above firmware on your Lava device, then make sure to take a backup of your data as it will be deleted after flashing the stock firmware.
▶️ Download and Install the Proper Drivers and Tools required before flashing.
▶️ If You Need Any Other Firmware or Flash File, Let Us Know.
