Lava Z52 Pro (LAVA_LH9910) is a budget-friendly Android smartphone released in India in 2022. While it may not boast high-end specs. Lava Z52 Pro is a good option for users on a tight budget who are looking for a basic smartphone for everyday tasks like making calls, sending text messages, and browsing the web. However, if you need a phone for gaming, photography, or other demanding tasks, you might want to consider a different model with more powerful specs.
Features of Lava Z52 Pro LH 9910 :
Display:
- 5.5-inch IPS LCD display with a resolution of 720 x 1280 pixels (267 ppi)
Processor and Performance:
- Unisoc SC9863A octa-core processor (1.6 GHz)
- 2GB of RAM
- 16GB of storage (expandable up to 128GB with microSD card)
Cameras:
- Rear: Dual camera system
- 8MP main sensor (f/2.0)
- 5MP secondary sensor (f/2.4)
- Front: 5MP selfie camera (f/2.2)
Battery:
- 4120mAh battery with 10W charging
Software:
- Android 11 (upgradable to Android 12)
Other Features:
- Fingerprint sensor
- Face unlock
- 3.5mm headphone jack
How to Flash Unisoc SPD Device :
Flashing a device with a Unisoc (Spreadtrum) System on Chip (SoC) involves a series of steps using flashing tools specific to Spreadtrum devices. Here’s a general guide on how to flash a Unisoc (Spreadtrum) CPU:
- Download Required Files:
- Download and install Spreadtrum USB drivers on your computer.
- Download the specific firmware or ROM intended for your device model. Ensure it’s compatible and meant for flashing through Spreadtrum flashing tools.
- Download Spreadtrum Upgrade Tool (also known as SPD Flash Tool) compatible with your device.
- Install Spreadtrum USB Drivers:
- Install the Spreadtrum USB drivers on your computer. This ensures that your computer can communicate with the device when it’s in bootloader or download mode.
- Extract Firmware/ROM:
- Extract the firmware or ROM file you downloaded earlier to a location on your computer. Make sure all necessary files are extracted and readily accessible.
- Launch Spreadtrum Upgrade Tool:
- Open the Spreadtrum Upgrade Tool (SPD Flash Tool) on your computer. It’s typically an executable file (.exe).
- Load Firmware:
- In the Spreadtrum Upgrade Tool, locate and select the firmware or ROM files you extracted earlier. These files usually have extensions like .pac or .pac.sc.
- Boot Device into Download Mode:
- Power off your device completely.
- Press and hold the required button combination to boot your device into download mode or bootloader mode. This combination may vary depending on the device model but commonly involves holding volume keys or a combination of volume and power buttons.
- Connect Device to Computer:
- Once your device is in download mode, connect it to your computer using a compatible USB cable. The Spreadtrum Upgrade Tool should recognize the device if the USB drivers are installed correctly.
- Begin Flashing:
- In the Spreadtrum Upgrade Tool, click on the “Start Downloading” or “Upgrade” button to initiate the flashing process.
- Wait for the flashing process to complete. Do not disconnect the device during this process.
- Completion and Reboot:
- Once the flashing process is complete, you should see a success message in the Spreadtrum Upgrade Tool.
- Safely disconnect your device from the computer.
- You can now boot your device into the system. It might take a while to boot up for the first time after flashing.
- Final Checks:
- After booting up, perform a factory reset on your device for optimal performance.
- Verify that the device is functioning correctly and that the new firmware or ROM has been successfully flashed.
Download Lava Z52 Pro LAVA LH9910 SPD CPU Firmware Flash File
Lava Z52 Pro LAVA LH9910 SPD CPU Firmware Flash File
Join Our Telegram Group. If you have any problems then comment below or message us. We try our best to help you. If you found this post and our site helpful then Dont forget to like and share our page.
Please Follow these Before Flashing :
▶️ Disclaimer: Firmware flashing is not an easy process and should be carried out only if you have enough knowledge. We are not responsible for any damage/ dead to your device.
▶️ Take a Backup: If you are going to flash the above firmware on your Lava device, then make sure to take a backup of your data as it will be deleted after flashing the stock firmware.
▶️ Download and Install the Proper Drivers and Tools required before flashing.
▶️ If You Need Any Other Firmware or Flash File, Let Us Know.
